Electricity is only needed during the magnetisation and demagnetisation phase, which lasts a few seconds.
    No problem in case of power failure. Magnetism is an inexhaustible source of energy.
    It only takes a few seconds to load and unload the work-piece from the working position.
    It can be used manually or be easily integrated into highly automated systems thanks to advanced electronic control.
  • Constant and evenly distributed force.
  • The electropermanent system easily adapts to work-pieces of varying designs and complexity.
  • The number and the cost of specific equipment is reduced.
  • Less deformation due to clamping and less equipment space.

Magnetic Matters

Understanding the benefits and limitations of different magnetic workholding technologies will help ensure that they are used appropriately and to their full potential.

Magnetic workholding has made moldmakers more efficient on the shop floor, but choosing the most appropriate technology and achieving optimal results requires a deeper understanding of the mechanics, benefits and limitations of the different available solutions. Three of these types of magnetic workholding devices are permanent magnetic, electromagnetic and electro-permanent magnetic chucks.

  • Permanent magnetic chucks. This type of workholding does not require electricity for activation or de-activation, but is instead mechanically activated with a simple lever. The magnets inside the chuck are always active, but when the lever is in the “off” position, the magnetic field is contained inside the chuck. When the lever is rotated to the “on” position, a mechanical grid slides and allows the magnetic field to extend outside the chuck and into the steel part that is being machined. This mechanical control means that a power failure will have no effect on the chuck’s hold on a part. Also, the permanent magnetic chuck does not emit any heat, so the part it is holding will not experience any heat distortion.  There are a few drawbacks to this type of workholding, however. Wear and tear on the internal moving parts and magnets will shorten the life of the permanent chuck, and its maximum size is typically restricted to 1000mm by 300mm, primarily because of the great mechanical force that would be required to activate it if it were any larger.

  • Electromagnetic chucks. Unlike in a permanent magnetic chuck, there are no actual magnets inside an electromagnetic chuck. Instead, a magnetic field is created when an electrical current is applied to a coil wrapped around a mild piece of steel inside the chuck. When there is no electrical current running through the coil, there is no magnetic field. 

    A benefit of this type of workholding is that there are no moving parts inside, so there is less internal wear and tear. In addition, the magnetic field height and the holding force of the chuck can be fine-tuned by applying more or less power. A disadvantage of an electro-magnetic chuck, however, is 
    that constant power is needed in order for it to hold the part, and this constant power can overheat the chuck and cause heat distortion of the parts. Also, a power failure will cause such a chuck to release a part, potentially causing an accident. 

  • Electro-permanent chucks. This is a mix of permanent magnetic and electromagnetic technologies. The inside of an electro-permanent chuck contains actual magnets composed primarily of alloys of aluminum, nickel and cobalt (alnico), as well as a coil that is wrapped around those magnets. A one- to two-second programmed electrical impulse sent into the coil will magnetize the alnico magnets, enabling the chuck to hold the part. With a reverse impulse, the alnico magnets become completely inactive, allowing full demagnetization of the parts being machined. 

    Some electro-permanent magnetic chucks also will contain additional neodymium magnets to increase holding force. These neodymium magnets cannot be fully demagnetized, however, leaving residual magnetism in the part. These chucks are more specifically called compensated electro-permanent systems.

    The primary benefit of using electro-permanent chucks in moldmaking is that they provide full access to the five sides of a mold. Because the part is magnetically clamped to the chuck, there is no need for vises that might get in the way of the tool path and require multiple workholding setups. These chucks allow for face milling, edge milling and even through-drilling in one setup. 

    Additionally, electro-permanent chucks do not require a constant power source to maintain activation, so the absence of power cords allows for full range of motion during machining with a moving or swivel table. Power is only needed for the two-second impulse that either magnetizes or demagnetizes the chuck. The chuck holds the part even during a power failure, and it remains cold, so there is no heat distortion of the parts. And, like the electromagnetic chuck, there are no moving parts inside, eliminating internal wear and tear.

    Naturally, with every pro comes a con. Electro-permanent chucks are more expensive than electromagnetic and permanent magnetic chucks, and their magnetic fields and power can be difficult to fine-tune. This is because the strength of electro-permanent chucks increases in irregular steps, unlike electromagnetic chucks, in which the increase in strength relates directly to how much power is running through the coils. 

Of course, magnetic workholding solutions aren’t limited to the three described here. The world of magnetics is always evolving, and great advances already have been made in the manufacture of lifting magnets, workholding magnets, filtration systems and magnetic quick-mold-change technology.

QUADSYSTEM: Strongest Neodium magnets in combination with high temperature resistant Alnico magnets

A new clamping technology that applies a permanent magnet and electricity that goes beyond your imagination

The winning technology

After many years of experience and research our magnetic team has successfully managed to improve on all the typical limitations of the obsolete electro-magnetic system, insecure, unreliable, subject to overheating and requiring constant maintenance.

The innovative electro permanent technology has enabled to build up electro permanent magnetic systems capable of ensuring GREAT STRENGTH, TOTAL SECURITY, LONG-TERM RELIABILITY.

The invertible double magnetic system comprises a series of independent square poles in a chess board arrangement and alternating N/S, capable of generating a high concentrated force through a mesh of multiple magnetic seams that permit the magnetic flux to circulate in a horizontal and flat field.

The clamping force generated enables the workplace to be held irrespective of the direction of the cutting force, even in the case of limited thicknesses, thanks to the limited depth of field.

Electric power is only used for a few seconds in the MAG (activation) and DEMAG (de-activation) phases: during processing the work piece is held exclusively by the force of the high-energy permanent magnets.

The system is in insensitive to possible current failures and is therefore "extra" safe. The absence of consumption enables energy to be saved and the clamping surface to be maintained in a "cold" condition with no deformations or expansions.

The force of the magnets remains constant indefinitely.

Super Electric Permanent magnetic chuck

Selecting the right solution

The standard series of Super-EPM chucks include more versions which have different performance characteristics. Capable of adapting to different operating needs, depending on the thickness. The surface condition (or the operating air gap) and the dimensions of the work piece to be clamped. The clamping force of each version depends on the different dimension types of poles and on the configurations of the magnetic area.

Each pair of N/S poles generates an autonomous and defined force which is not influenced by the operating conditions of the other adjacent poles. Therefore by counting the number of poles occupied by the clamped piece it is possible to predetermine the force generated and consequently to establish the usable machine power with the relative machining parameters.

As an indication we can say that a pair of size 50 poles (50*50mm) can enable processing of up to 2 kw machine absorption, while a pair of size 75 poles (75*75mm) can absorb up to 4 kw.